| Specialized ICs | 1 | Active | |
L99MD01Octal Half-Bridge Driver with SPI control for Automotive Application | Power Management - Specialized | 1 | Active | The L99MD01 is an octal half-bridge driver for automotive applications.
The device is intended to drive DC and/or stepper motors. Using the boost converter it’s possible to drive 4 stepper motors simultaneously. Without boost converter the system is able to run 3 stepper motors in sequential mode or 2 stepper motors simultaneously. The octal half bridge configuration allows also to drive 4 DC-motors simultaneously and 7 DC-motors sequentially.
The integrated 24 bit standard Serial Peripheral Interface (SPI) controls all outputs and provides diagnostic information: normal operation, open-load in on-state, overcurrent, temperature warning and overtemperature. |
L99MD02Hexa Half-Bridge Driver with SPI control for Automotive Application | Power Management (PMIC) | 1 | Active | The L99MD02 IC is a 6 x half bridge driver for automotive applications. The device is intended to drive DC-motors. It is possible to drive 3 DC-motors simultaneously or up to 5 DC-motors sequentially.
The integrated 24 bit standard serial peripheral interface (SPI) controls all outputs and provides diagnostic information: normal operation, open-load in on-state, overcurrent, temperature warning and overtemperature. |
L99MM70XPIntegrated Microprocessor driven device intended for LIN controlled exterior mirrors | Integrated Circuits (ICs) | 1 | Active | The L99MM70XP is a microcontroller driven multifunctional system ASSP dedicated for LIN controlled wing mirror applications. The device contains a voltage regulator to supply the microcontroller and a LIN2.1 physical layer. Up to 3 DC motors and five grounded resistive loads can independently be driven with four (five) half bridges and five high-side driver. The EC-glass control block provides overvoltage protection with a fast discharge path versus GND and a negative discharge path for future EC-glass characteristics. The integrated ST SPI controls all operation modes (forward, reverse, brake and high-impedance) and provides all the diagnostic information. |
L99PM62XPPower management IC with LIN and high speed CAN | Integrated Circuits (ICs) | 1 | Active | The L99PM62XP is a power management system IC providing electronic control units with enhanced system power supply functionality including various standby modes as well as LIN and HS CAN physical communication layers. It contains two low drop voltage regulators to supply the system microcontroller and external peripheral loads such as sensors and provides enhanced system standby functionality with programmable local and remote wake up capability.
In addition, five high-side drivers, two low-side drivers and two operational amplifiers increase the system integration level.
The ST standard SPI interface (3.0) allows control and diagnosis of the device and enables generic software development. |
| Integrated Circuits (ICs) | 1 | Active | The L99UDL01 is a multiple half-bridge IC with 6 integrated outputs that are PWM configurable and current regulated and up to two externally configured half bridges for higher current nodes. The level of diagnostics includes open load, short to battery, short to ground, and load integrity via 10 bit current feedback.
The L99UDL01 is commanded entirely by SPI using duration and current level commands. |
LCP02Protection IC for ringing SLICs | Transient Voltage Suppressors (TVS) | 1 | Obsolete | The LCP02 has been developed to protect SLICs operating on both negative and positive battery supplies, as well as high voltage SLICs. It provides crowbar mode protection for both TIP and RING lines. The surge suppression is assumed for each wire by two thyristor structures, one dedicated to positive surges the second one for negative surges. Both positive and negative threshold levels are programmable by two gates.
LCP02 can be used to help equipment to meet various standards such as UL1950, IEC 60950 / CSAC22.2, UL1459 and TIA-968-A. LCP02 pinout and clearance is compatible with UL60950. Resin meets UL94 V0.
LCP02 is UL497B approved - file: E136224. |
| Thyristors | 1 | Obsolete | |
LCP154DJFProgrammable transient voltage suppressor for SLIC protection | Circuit Protection | 1 | Active | This device has been especially designed to protect new high voltage, as well as classical SLICs, against transient overvoltages.
Positive overvoltages are clamped by 2 diodes. Negative surges are suppressed by 2 thyristors, their breakdown voltage being referenced to -VBATthrough the gate.
LCP154DJF is specified to comply with ITU-T K20/21/45 and GR1089-Core when associated with Cooper Bussmann Telecom Circuit Protector fuse TCP 1.25 A.
LCP154DJF is packaged in a PowerFLAT™ 5x6 to meet IEC/UL 60950 clearance requirements. |
| PMIC | 3 | Obsolete | |
