S
STMicroelectronics
| Series | Category | # Parts | Status | Description |
|---|---|---|---|---|
| Part | Spec A | Spec B | Spec C | Spec D | Description |
|---|---|---|---|---|---|
Beta
⌘K
| Series | Category | # Parts | Status | Description |
|---|---|---|---|---|
| Part | Spec A | Spec B | Spec C | Spec D | Description |
|---|---|---|---|---|---|
| Part | Category | Description |
|---|---|---|
STMicroelectronics EMIF09-SD01F3Obsolete | Filters | FILTER RC(PI) 40 OHM/20PF SMD |
 STMicroelectronics | Integrated Circuits (ICs) | STM32 DYNAMIC EFFICIENCY MCU WITH BAM, HIGH-PERFORMANCE AND DSP WITH FPU, ARM CORTEX-M4 MCU WITH 1 MBYTE OF FLASH MEMORY, 100 MHZ CPU, ART ACCELERATOR, DFSDM |
 STMicroelectronics | Integrated Circuits (ICs) | 32-BIT POWER ARCHITECTURE MCU FOR AUTOMOTIVE BODY AND GATEWAY APPLICATIONS |
STMicroelectronics | Integrated Circuits (ICs) | MCU 32-BIT E200Z0H RISC 128KB FLASH 3.3V/5V AUTOMOTIVE AEC-Q100 64-PIN LQFP T/R |
 STMicroelectronics | Development Boards Kits Programmers | DEMONSTRATION BOARD FOR SINGLE CHANNEL OP-AMP IN SO8 PACKAGE |
 STMicroelectronics LDLN025J30RLTB | Integrated Circuits (ICs) | IC REG LINEAR 3V 250MA 4FLIPCHIP |
 STMicroelectronics ST25RU3993-EVALObsolete | Development Boards Kits Programmers | ST25RU3993 READER IC EVALUATION BOARD |
 STMicroelectronics | Integrated Circuits (ICs) | ARM-BASED 32-BIT MCU+FPU, 84MHZ, 128KB FLASH, 49-PIN WLCSP, -40 TO 85°C T/R |
 STMicroelectronics STP12NM60NObsolete | Discrete Semiconductor Products | MOSFET N-CH 600V 10A TO220AB |
 STMicroelectronics VND1NV04Obsolete | Integrated Circuits (ICs) | IC PWR DRIVER N-CHANNEL 1:1 DPAK |
| Series | Category | # Parts | Status | Description |
|---|---|---|---|---|
| Bipolar (BJT) | 1 | Obsolete | ||
EV-VN5016AJVN5016AJ Evaluation Board | Power Distribution Switches, Load Drivers | 2 | Active | EV-VN5016AJ provides you an easy way to connect ST’s surface mounted VIPower®drivers into your existing prototype circuitry. This evaluation board comes pre-assembled with VN5016AJ-E high-side driver.
The VN5016AJ-E is a monolithic device made using STMicroelectronics®VIPower®M0-5 technology. It is intended for driving resistive or inductive loads with one side connected to ground.
Active VCCpin voltage clamp protects the device against low energy spikes. This device integrates an analog current sense which delivers a current proportional to the load current (according to a known ratio) when CS_DIS is driven low or left open. When CS_DIS is driven high, the CURRENT SENSE pin is in a high impedance condition.
Output current limitation protects the device in overload condition. In case of long overload duration, the device limits the dissipated power to safe level up to thermal shutdown intervention. Thermal shutdown with automatic restart allows the device to recover normal operation as soon as fault condition disappears. |
EV-VN5E050AJVN5E050AJ Evaluation board | Power Management (PMIC) | 3 | Active | EV-VN5E050AJ provides you an easy way to connect ST’s surface mounted VIPower®drivers into your existing prototype circuitry. This evaluation board comes pre-assembled with VN5E050AJ-E high-side driver.
The VN5E050AJ-E is a single channel high-side driver manufactured using ST proprietary VIPower M0-5 technology and housed in PowerSSO-12 package. The VN5E050AJ-E is designed to drive 12V automotive grounded loads, providing protection, diagnostics and easy 3 V and 5 V CMOS-compatible interface with any microcontroller.
The device integrates advanced protective functions such as load current limitation, inrush and overload active management by power limitation, overtemperature shut-off with auto-restart and overvoltage active clamp. A dedicated analog current sense pin is associated with every output channel provides enhanced diagnostic functions including fast detection of overload and short-circuit to ground through power limitation indication, overtemperature indication, short-circuit to VCCdiagnosis and ON-state and OFF-state open-load detection.
The current sensing and diagnostic feedback of the whole device can be disabled by pulling the CS_DIS pin high to share the external sense resistor with similar devices. |
EV-VN7003ALHVN7003ALH Evaluation Board | Evaluation and Demonstration Boards and Kits | 2 | Active | This board provides you an easy way to connect STMicroelectronics®VIPower®M0-7 technology into your existing system. |
EV-VN7004CLHVN7004CLH Evaluation Board | Evaluation Boards | 1 | Active | This board provides you an easy way to connect STMicroelectronics®VIPower®M0-7 technology into your existing system. |
EV-VN7016AJVN7016AJ Evaluation Board | Evaluation Boards | 1 | Active | This board provides you an easy way to connect STMicroelectronics®VIPower®M0-7 technology into your existing system. |
EV-VN7040AJVN7040AJ evaluation board | Evaluation Boards | 1 | Active | This board provides you an easy way to connect STMicroelectronics®VIPower®M0-7 technology into your existing system. |
EV-VN9004AJVN9004AJ evaluation board | Development Boards, Kits, Programmers | 1 | Active | The EV-VN9004AJ board provides an easy way to connect VN9004AJ into existing system. |
EV-VN9008AJVN9008AJ evaluation board | Evaluation and Demonstration Boards and Kits | 1 | Active | The EV-VN9008AJ board provides an easy way to connect VN9008AJ into existing system. |
EV-VN9D30Q100FVN9D30Q100F Evaluation Board | Development Boards, Kits, Programmers | 1 | Active | The EV-VN9D30Q100F board provides an easy way to connect ST VIPower M0-9SPI technology into existing system. |