Specification	TPPM0115D

Clock Sync	False
Control Features	Phase Control, Power Good
Frequency - Switching	200 kHz
Function	Step-Down
Mounting Type	Surface Mount
Number of Outputs	2
Operating Temperature [Max]	70 °C
Operating Temperature [Min]	0 °C
Output Configuration	Positive
Output Phases	2
Output Type	Transistor Driver
Package / Case	8-SOIC
Package / Case [x]	0.154 in
Package / Case [y]	3.9 mm
Supplier Device Package	8-SOIC
Synchronous Rectifier	True
Topology	Buck
Voltage - Supply (Vcc/Vdd) [Max]	12.6 V
Voltage - Supply (Vcc/Vdd) [Min]	11.4 V

TPPM0115 Series

Part	Output Type	Function	Supplier Device Package	Package / Case	Package / Case [y]	Package / Case [x]	Frequency - Switching	Control Features	Mounting Type	Output Configuration	Operating Temperature [Max]	Number of Outputs	Output Phases	Topology	Voltage - Supply (Vcc/Vdd) [Min]	Voltage - Supply (Vcc/Vdd) [Max]
Texas Instruments TPPM0115DG4	Transistor Driver	Step-Down	8-SOIC	8-SOIC	3.9 mm	0.154 in	200 kHz	Phase Control Power Good	Surface Mount	Positive	70 °C	2	2	Buck	11.4 V	12.6 V
Texas Instruments TPPM0115DR	Transistor Driver	Step-Down	8-SOIC	8-SOIC	3.9 mm	0.154 in	200 kHz	Phase Control Power Good	Surface Mount	Positive	70 °C	2	2	Buck	11.4 V	12.6 V
Texas Instruments TPPM0115D	Transistor Driver	Step-Down	8-SOIC	8-SOIC	3.9 mm	0.154 in	200 kHz	Phase Control Power Good	Surface Mount	Positive	70 °C	2	2	Buck	11.4 V	12.6 V

Pricing

Prices provided here are for design reference only. For realtime values and availability, please visit the distributors directly

Distributor	Package	Quantity	$

Digikey	Tube	1	$ 5.27
		10	$ 4.74
		75	$ 4.48
		150	$ 3.88
		300	$ 3.68
		525	$ 3.30
		1050	$ 2.79
		2550	$ 2.65
Texas Instruments	TUBE	1	$ 4.62
		100	$ 3.77
		250	$ 2.96
		1000	$ 2.51

Description

General part information

TPPM0115 Series

The TPPM0115 is a synchronous buck controller capable of driving two external power FETs 180° out of phase. The device requires a minimum of external standard filter components and switching FETs to regulate the desired output voltage. This is achieved with an internal switching frequency of 200 kHz (typical).

The TPPM0115 switch mode controller and associated circuitry provide efficient voltage regulation of greater than 85%. The output voltage is set by two external resistors. During power up, when the output voltage reaches 90% of the desired value, the power good (PWRGD) output is transitioned high after a short delay of 1 ms to 5 ms. During power down, when the output voltage falls below 90% of the set value, the PWRGD output is pulled low without any delay.

In the event the set output is in an over-voltage condition due to a system fault, the drive to the lower FET turns on to correct the fault. There is a dead time between switching one FET ON while the other FET is switching OFF to prevent cross conduction.

Documents

Technical documentation and resources

Switch Mode Synchronous Buck Controller datasheet (Rev. A)

Data sheet