MCP2562FD Series

High-speed CAN FD Transceiver with Standby Mode and VIO Pin

Catalog

High-speed CAN FD Transceiver with Standby Mode and VIO Pin

Part	Operating Temperature [Max]	Operating Temperature [Min]	Type	Voltage - Supply [Min]	Voltage - Supply [Max]	Duplex	Supplier Device Package	Protocol	Mounting Type	Package / Case	Package / Case [y]	Package / Case [x]	Receiver Hysteresis	Data Rate	Package / Case	Package / Case	Grade	Qualification
Microchip Technology MCP2562T-E/SN	125 °C	-40 °C	Transceiver	4.5 V	5.5 V	Half	8-SOIC	CANbus	Surface Mount	8-SOIC	3.9 mm	0.154 in	200 mV
Microchip Technology MCP2562FDT-E/MF	125 °C	-40 °C	Transceiver	4.5 V	5.5 V		8-DFN (3x3)	CANbus	Surface Mount	8-VDFN Exposed Pad			200 mV	8 Mbps
Microchip Technology MCP2562-H/SN			Transceiver	4.5 V	5.5 V	Half	8-SOIC	CANbus	Surface Mount	8-SOIC	3.9 mm	0.154 in
Microchip Technology MCP2562FD-H/MF			Transceiver	4.5 V	5.5 V		8-DFN (3x3)	CANbus	Surface Mount	8-VDFN Exposed Pad			200 mV	8 Mbps
Microchip Technology MCP2562-E/P	125 °C	-40 °C	Transceiver	4.5 V	5.5 V	Half	8-PDIP	CANbus	Through Hole	8-DIP					0.3 in	7.62 mm
Microchip Technology MCP2562T-E/MF	125 °C	-40 °C	Transceiver	4.5 V	5.5 V	Half	8-DFN (3x3)	CANbus	Surface Mount	8-VDFN Exposed Pad			200 mV
Microchip Technology MCP2562FDT-E/MFVAO	125 °C	-40 °C	Transceiver	4.5 V	5.5 V	Half	8-DFN (3x3)	CANbus	Surface Mount	8-VDFN Exposed Pad			200 mV	8 Mbps			Automotive	AEC-Q100
Microchip Technology MCP2562T-H/MF			Transceiver	4.5 V	5.5 V	Half	8-DFN (3x3)	CANbus	Surface Mount	8-VDFN Exposed Pad			200 mV
Microchip Technology MCP2562FD-E/P	125 °C	-40 °C	Transceiver	4.5 V	5.5 V		8-PDIP	CANbus	Through Hole	8-DIP			200 mV	8 Mbps	0.3 in	7.62 mm
Microchip Technology MCP2562FD-H/SN			Transceiver	4.5 V	5.5 V		8-SOIC	CANbus	Surface Mount	8-SOIC	3.9 mm	0.154 in	200 mV	8 Mbps

Catalog

High-speed CAN FD Transceiver with Standby Mode and VIO Pin

Key Features

• * Supports 1 Mb/s operation

• * Implements ISO-11898-5 standard physical layerrequirements

• * AEC-Q100 Grade 0

• * Very low standby current (Typ: 5µA)

• * VIO supply pin (MCP2562) to interface directly to CAN controllers and microcontrollers with 1.8V to 5V I/O

• * SPLIT output pin (MCP2561) to stabilize common mode in biased split termination schemes

• * CAN bus pins are disconnected when device is unpowered. An unpowered node or brown-out event will not load the CAN bus

• * Detection of ground fault; Permanent dominant detection on TXD, Permanent dominant detection on bus

• * Power-on Reset and voltage brown-out protectionon VDD and VIO pin

• * Protection against damage due to short-circuitconditions (positive or negative battery voltage)

• * Protection against high-voltage transients in automotive environments

• * Automatic Thermal Shutdown protection

• * Suitable for 12V and 24V systems

• * Up to 112 nodes can be connected

• * High-noise immunity due to differential bus implementation

• * High ESD protection on CANH and CANL, IEC61000-4-2 > 8kV

• * Available in PDIP-8L, SOIC-8L and 3x3 DFN-8L.

• * Temperature ranges; Extended (E): -40°C to +125°C, High (H): -40°C to +150°C

Description

The MCP2561/2FD is a Microchip Technology Inc. second generation high-speed CAN transceiver. It offers the same features as the MCP2561/2. Additionally, it guarantees Loop Delay Symmetry in order to support the higher data rates required for CAN FD. The maximum propagation delay was improved to support longer bus length. The device meets the automotive requirements for CAN FD bit rates exceeding 5 Mbps, low quiescent current, electromagnetic compatibility (EMC) and electrostatic discharge (ESD). The device family members are MCP2561FD with SPLIT pin and MCP2562FD with VIO pin. **For 12V applications please consider the ATA6561**