TPS65288RHAT
Active4.5V TO 18V INPUT, 3A/2A/2A TRIPLE SYNCHRONOUS BUCK CONVERTER WITH DUAL LOAD SWITCHES
Deep-Dive with AI
Search across all available documentation for this part.
TPS65288RHAT
Active4.5V TO 18V INPUT, 3A/2A/2A TRIPLE SYNCHRONOUS BUCK CONVERTER WITH DUAL LOAD SWITCHES
Deep-Dive with AI
Technical Specifications
Parameters and characteristics for this part
| Specification | TPS65288RHAT |
|---|---|
| Current - Output | 2 A, 3 A |
| Frequency - Switching [Max] | 2.2 MHz |
| Frequency - Switching [Min] | 300 kHz |
| Function | Step-Down |
| Mounting Type | Surface Mount |
| Number of Outputs | 3 |
| Operating Temperature [Max] | 85 °C |
| Operating Temperature [Min] | -40 °C |
| Output Configuration | Positive |
| Output Type | Adjustable |
| Package / Case | 40-VFQFN Exposed Pad |
| Supplier Device Package | 40-VQFN (6x6) |
| Synchronous Rectifier | True |
| Topology | Buck |
| Voltage - Input (Max) [Max] | 18 V |
| Voltage - Input (Min) [Min] | 4.5 V |
| Voltage - Output (Max) [Max] | 17 V |
| Voltage - Output (Min/Fixed) | 0.8 V |
Pricing
Prices provided here are for design reference only. For realtime values and availability, please visit the distributors directly
| Distributor | Package | Quantity | $ | |
|---|---|---|---|---|
| Digikey | Cut Tape (CT) | 1 | $ 6.50 | |
| 10 | $ 5.84 | |||
| 25 | $ 5.52 | |||
| 100 | $ 4.78 | |||
| Digi-Reel® | 1 | $ 6.50 | ||
| 10 | $ 5.84 | |||
| 25 | $ 5.52 | |||
| 100 | $ 4.78 | |||
| Tape & Reel (TR) | 250 | $ 4.54 | ||
| 500 | $ 4.07 | |||
| 1250 | $ 3.43 | |||
| 2500 | $ 3.26 | |||
| Texas Instruments | SMALL T&R | 1 | $ 4.47 | |
| 100 | $ 3.64 | |||
| 250 | $ 2.86 | |||
| 1000 | $ 2.43 | |||
Description
General part information
TPS65288 Series
TPS65288 is a power management IC with three step-down buck converters. Both high-side and low-side MOSFETs are integrated to provide fully synchronous conversion with higher efficiency. The converters are designed to simplify its application while giving the designer the option to optimize their usage according to the target application.
The converters can operate in 5-, 9-, 12- or 15-V systems. The output voltage can be set externally using a resistor divider to any value between 0.8 V and the input supply minus the resistive drops on the converter path. Each converter features enable pin that allows a delayed start-up for sequencing purposes, soft start pin that allows adjustable soft-start time by choosing the soft-start capacitor, and a current limit (RLIM) pin that enables designer to adjust current limit by selecting an external resistor and optimize the choice of inductor. All converters operate in ‘hiccup mode’: Once an over-current lasting more than 10 ms is sensed in any of the converters, they will shut down for 10 ms and then the start-up sequencing will be tried again. If the overload has been removed, the converter will ramp up and operate normally. If this is not the case the converter will see another over-current event and shuts down again repeating the cycle (hiccup) until the failure is cleared. If an overload condition lasts for less than 10 ms, only the relevant converter affected will shut-down and re-start and no global hiccup mode will occur.
The switching frequency of the converters is set by an external resistor connected to ROSC pin. The switching regulators are designed to operate from 300 kHz to 2.2 MHz. The converters operate with 180° phase between then to minimize the input filter requirements. All converters have peak current mode control which simplifies external frequency compensation.
Documents
Technical documentation and resources
