
MAX22208AUU+T
Active65V, 3.8A QUAD HALF H-BRIDGE DRIVERS WITH INTEGRATED CURRENT SENSE
Deep-Dive with AI
Search across all available documentation for this part.

MAX22208AUU+T
Active65V, 3.8A QUAD HALF H-BRIDGE DRIVERS WITH INTEGRATED CURRENT SENSE
Deep-Dive with AI
Technical Specifications
Parameters and characteristics for this part
| Specification | MAX22208AUU+T |
|---|---|
| Applications | DC Motors, Solenoids |
| Current - Output / Channel | 2 A |
| Current - Peak Output | 3.8 A |
| Fault Protection | Current Limiting, UVLO, Over Temperature |
| Features | Charge Pump |
| Interface | PWM |
| Load Type | Inductive |
| Mounting Type | Surface Mount |
| Operating Temperature [Max] | 125 °C |
| Operating Temperature [Min] | -40 C |
| Output Configuration | Half Bridge (4) |
| Package / Case | 38-TFSOP, Exposed Pad |
| Package / Case | 4.4 mm, 0.173 " |
| Rds On (Typ) [custom] | 150 mOhm |
| Rds On (Typ) [custom] | 150 mOhm |
| Supplier Device Package | 38-TSSOP-EP |
| Technology | NMOS |
| Voltage - Load [Max] | 65 V |
| Voltage - Load [Min] | 4.5 V |
Pricing
Prices provided here are for design reference only. For realtime values and availability, please visit the distributors directly
| Distributor | Package | Quantity | $ | |
|---|---|---|---|---|
| Digikey | N/A | 0 | $ 3.55 | |
Description
General part information
MAX22208 Series
The MAX22208 provides four individually controllable 65V, 3.8AMAXhalf H-bridge drivers. It can be used to drive four solenoids, two brushed DC motors, one single stepper motor, or a combination of different loads.The power FETs have very low impedance, resulting in high driving efficiency and low heat dissipation. The typical total RON(high side plus low side) is 0.3Ω (typ).Each half bridge can be individually pulse-width modulation (PWM)-controlled with two logic inputs (DIN_, EN_).The MAX22208 integrates non-dissipative current sensing, which eliminates the bulky external power resistors normally required for this function, resulting in a dramatic space and power saving compared with mainstream applications based on the external sense resistor.A current proportional to the internally-sensed load current is output to the external current-monitor pins (ISEN_). By connecting an external resistor to these pins, a voltage proportional to the motor current is generated. The voltage drop across the external resistors can be input into the controller ADC whenever the control algorithm requires the current/torque information.The maximum output current per half H-bridge is IMAX= 3.8A and is limited by the overcurrent protection (OCP) circuit. This current can be driven for very short transients and aims to effectively drive small capacitive loads.The maximum RMS current per H-bridge is IRMS= 2A. Since this current is limited by thermal considerations, the actual maximum RMS current depends on the thermal characteristic of the application (PCB ground planes, heatsinks, forced air ventilation, etc.).The MAX22208 features overcurrent protection (OCP), thermal shutdown (TSD), and undervoltage lockout (UVLO). An active-low, open-drainFAULTpin is activated every time a fault condition is detected.During TSD and UVLO, the driver outputs are three-stated until normal operating conditions are restored.The MAX22208 is available in a small, 5mm x 7mm, 38-pin TQFN and 4.4mm x 9.7mm, 38-pin TSSOP package.APPLICATIONSBrushed DC Motor DriverStepper Motor DriverSolenoid DriverLatched Valves
Documents
Technical documentation and resources