ON Semiconductor

The FTCO3V455A1 is a 40 V low Rds(on) automotive qualified power integrated module (PIM) featuring a 3-phase MOSFET inverter optimized for 12 V battery systems. It includes a precision shunt resistor for current sensing an NTC for temperature sensing and an RCsnubber circuit. The module utilizes trench MOSFET technology and it is designed to provide a very compact and high performance variable speed motor drive for applications like electric power steering, electro-hydraulic power steering, electric water pumps,electric oil pumps. The power module is UL compliant.

The FTL11639 is both a timer for resetting a mobile device and an advanced load management device for applications requiring a highly integrated solution.If the mobile device is off, holding /SR0 LOW (by pressing power-on key) for 38 ms ±20% turns on the PMIC.As a reset timer, it has one input and one fixed delay output. It generates a fixed delay of 11.5 s ±20% by disconnecting the PMIC from the battery power supply. FTL11639 does not accept a new input signal for 400 ms ±20% to give the PMIC enough time to turn off.The reset delay can be customized by connecting an external resistor to the DELAY_ADJ pin.As an advanced load management switch, the FTL11639 disconnects loads powered from the DC power rail (<6 V) with stringent off-state current targets and high load capacitances (up to 200 µF). The FTL11639 consists of a slew-rate controlled low-impedance MOSFET switch (21 mΏ typical at 4.5 V) that has exceptionally low off-state current drain (<0.2 µA typical) to facilitate compliance with standby power requirements. The slew-rate-controlled turn-on characteristic prevents inrush current and the resulting excessive voltage drop on power rails.The low ICCTenables direct interface to lower-voltage chipsets without external translation, while maintaining low power consumption.The device is packaged in advanced, fully "green," 1.31 mm x 1.62 mm, Wafer-Level Chip-Scale Packaging (WLCSP); providing excellent thermal conductivity, small footprint, and low electrical resistance for a wide application range.

The FTL7522 is a timer for resetting a mobile device where long reset times are needed. The long delay helps avoid unintended resets caused by accidental key presses. It has a fixed delay of 7.5 ±20% seconds. The DSR pin enables Test Mode operation by immediately forcing /RST1 LOW for factory testing.The FTL7522 has one input for single-button resetting capability. The device has a single open-drain output with 0.5mA pull-down drive.FTL7522 draws minimal ICCcurrent when inactive and functions over a power supply range of 1.65V to 5.0V.The FTL7522 low-ICCTfeature enables direct interface with lower-voltage chipsets without needing external translation, while maintaining low power consumption.

The FUSB15200 is a highly integrated dual port USB Type−C and Power Delivery Controller optimized for Sink and DRP  applications.The FUSB15200 enables a complete solution through optimized hardware peripherals and complete open−source embedded firmware all in a compact solution. Maximizing total system power budgets is enabled through both hardware and firmware of the FUSB15200.onsemi offers a complete open−source embedded firmware solution. System designers can easily tailor this firmware to meet  the specific needs of their end application through an easy to use API for the embedded firmware. The FUSB15200 also  provides a completely USB PD3.1 compliant solution with interoperability with leading mobile and computing devices in the market.

The FUSB15201 is a dual port USB Type−C & PD controller for power source applications. The FUSB15201 integrates a highly efficient Arm® Cortex®−M0+ processor with custom designed peripherals to seamlessly support USB PD 3.0 applications.  Integrating all the requirements of power ports providing an optimal system solution that can be easily customized to the specific application needs.  Delivering a full embedded firmware solution with advanced power sharing algorithms which optimize total system power efficiently and effectively.

The FUSB251 is an I2C controlled over voltage protection switch on CC and SBU pins in USB Type−C™ interface port. The device has SPST switches on CC1/2 and SBU1/2 which are enabled automatically with valid VDD so that Type−C™ PD controller can use the over voltage protected CC path. The FUSB251 has dead battery mode and CC pulled down with Rd so the source device can provide Vbus for battery charging. Another feature of the FUSB251 is moisture detection on both the CC and SBU paths with ADC detection. Once moisture is detected an interrupt is generated and corresponding the register is updated to notify the host. The device has on−chip IEC protection with surge protection on both CC and SBU paths. Both CC and SBU ports are 20 V DC tolerant.