O
ON Semiconductor
| Series | Category | # Parts | Status | Description |
|---|---|---|---|---|
| Part | Spec A | Spec B | Spec C | Spec D | Description |
|---|---|---|---|---|---|
Beta
⌘K
| Series | Category | # Parts | Status | Description |
|---|---|---|---|---|
| Part | Spec A | Spec B | Spec C | Spec D | Description |
|---|---|---|---|---|---|
| Part | Category | Description |
|---|---|---|
 ON Semiconductor | Integrated Circuits (ICs) | SELF-PROTECTED N-CHANNEL POWER MOSFET/ REEL |
 ON Semiconductor 74AC32PCObsolete | Integrated Circuits (ICs) | IC GATE OR 4CH 2-INP 14MDIP |
 ON Semiconductor | Discrete Semiconductor Products | IGBT, 360V, 27A, 1.32V, 320MJ, TO-262<BR>ECOSPARK® I, N-CHANNEL IGNITION |
 ON Semiconductor FAN1655MTFXObsolete | Integrated Circuits (ICs) | IC REG CTRLR DDR 1OUT 16TSSOP |
 ON Semiconductor FIN1027MObsolete | Integrated Circuits (ICs) | LVDS DRIVER, LVDS DIFFERENTIAL DRIVER, -40 °C, 85 °C, 3 V, 3.6 V, SOIC |
 ON Semiconductor | Integrated Circuits (ICs) | PIPELINE REGISTER, 8-BIT PQCC28 |
ON Semiconductor SLV4HC4053ADWRGObsolete | Integrated Circuits (ICs) | LDO REGULATOR, ULTRA-LOW NOISE, |
 ON Semiconductor | Isolators | OPTOCOUPLER, DIP, 6 PINS, 5 KV, NON ZERO CROSSING, 800 V, FOD4218 SERIES |
 ON Semiconductor NVMFD5483NLT1GObsolete | Discrete Semiconductor Products | DUAL N-CHANNEL POWER MOSFET 60V, 24A, 36MΩ |
ON Semiconductor | Discrete Semiconductor Products | BIP NPN 8A 50V |
| Series | Category | # Parts | Status | Description |
|---|---|---|---|---|
| Transistors | 1 | Active | ||
| IGBT Modules | 2 | Active | ||
| Integrated Circuits (ICs) | 1 | Obsolete | ||
| PMIC | 2 | Active | ||
FPF2003Full Function Load Switches | Power Distribution Switches, Load Drivers | 1 | Active | The FPF2000 through FPF2007 is a family of load switches which provide full protection to systems and loads which may encounter large current conditions. These devices contain a 0.7W current-limited P-channel MOSFET which can operate over an input voltage range of 1.8-5.5V. Switch control is by a logic input (ON) capable of interfacing directly with low voltage control signals. Each part contains thermal shutdown protection which shuts off the switch to prevent damage to the part when a continuous over-current condition causes excessive heating. When the switch current reaches the current limit, the part operates in a constant current mode to prohibit excessive currents from causing damage. For the FPF2000-FPF2002 and FPF2004-FPF2006, if the constant current condition still persists after 10ms, these parts will shut off the switch and pull the fault signal pin (FLAGB) low. The FPF2000, FPF2001, FPF2004 and FPF2005, have an auto-restart feature which will turn the switch on again after 80ms if the ON pin is still active. The FPF2002 and FPF2006 do not have this auto-restart feature so the switch will remain off until the ON pin is cycled. For the FPF2003 and FPF2007, a current limit condition will immediately pull the fault signal pin low and the part will remain in the constant-current mode until the switch current falls below the current limit. For the FPF2000 through FPF2003, the minimum current limit is 50mA while that for the FPF2004 through FPF2007 is 100mA. These parts are available in a space-saving 5 pin SC-70 package. |
FPF2004Full Function Load Switches | Power Management (PMIC) | 1 | Active | The FPF2000 through FPF2007 is a family of load switches which provide full protection to systems and loads which may encounter large current conditions. These devices contain a 0.7W current-limited P-channel MOSFET which can operate over an input voltage range of 1.8-5.5V. Switch control is by a logic input (ON) capable of interfacing directly with low voltage control signals. Each part contains thermal shutdown protection which shuts off the switch to prevent damage to the part when a continuous over-current condition causes excessive heating. When the switch current reaches the current limit, the part operates in a constant current mode to prohibit excessive currents from causing damage. For the FPF2000-FPF2002 and FPF2004-FPF2006, if the constant current condition still persists after 10ms, these parts will shut off the switch and pull the fault signal pin (FLAGB) low. The FPF2000, FPF2001, FPF2004 and FPF2005, have an auto-restart feature which will turn the switch on again after 80ms if the ON pin is still active. The FPF2002 and FPF2006 do not have this auto-restart feature so the switch will remain off until the ON pin is cycled. For the FPF2003 and FPF2007, a current limit condition will immediately pull the fault signal pin low and the part will remain in the constant-current mode until the switch current falls below the current limit. For the FPF2000 through FPF2003, the minimum current limit is 50mA while that for the FPF2004 through FPF2007 is 100mA. These parts are available in a space-saving 5 pin SC-70 package. |
| Power Distribution Switches, Load Drivers | 1 | Obsolete | ||
| Power Distribution Switches, Load Drivers | 2 | Obsolete | ||
| Integrated Circuits (ICs) | 1 | Obsolete | ||
| Power Management (PMIC) | 1 | Obsolete | ||