PD-POE-EXTENDERPoE extender to extend the Ethernet network range beyond 100m | External/Internal Power Supply Accessories | 1 | Active | With the PoE-extender, you can easily improve the range and placement of your wireless and surveillance networks and therefore the strength of your networks. PD-POE-Extender is a cost-effective way to extend the Ethernet network range beyond 100m, the PoE-extender will deliver both data and power to network devices up to 200m while complying with IEEE PoE and data standards.
The PoE-extender has both a PD and a PSE chip inside so both the power and the data may be reliably transmitted beyond 100m. The extender acts as a pass-through with data-repeating capabilities.
It can be cascaded to reach up to 500m from the closest datacenter or network closet so you can easily install WLAN APs, IP cameras and access controllers where you need them. |
PD39210IEEE 802.3af/at PoE Controller | Embedded | 6 | Active | PD39210 is a Microchip-based cost-effective,
pre-programmed MCU designed to implement complete PoE control in
conjunction with the PD39208 PSE Manager. The PD39210 features a SPI bus
to connect up to six PD39208 PSE Managers.
It has an embedded ARM Cortex™-M0+ core. The
controller uses I2C or UART interface to the host CPU and is
designed to support software field upgradable through the communication
interface.
PD39210 is available in 32 pin, 5 mm x 5 mm QFN package. |
| Power Management (PMIC) | 1 | Active | |
| Power Over Ethernet (PoE) Controllers | 1 | Active | |
| Integrated Circuits (ICs) | 1 | Obsolete | |
| Power Over Ethernet (PoE) Controllers | 1 | Obsolete | |
PD69101IEEE 802.3at single port PoE PSE controller + manager, industrial temp | Integrated Circuits (ICs) | 2 | Active | A single port, mixed-signal, high-voltage PoE driver. The device is utilized in Ethernet switches and enables network devices to share power and data over the same cable.
It enables detection of IEEE 802.3af-2003 compliant PDs (Powered Devices) and IEEE 802.3at high power devices ensuring safe power feeding and disconnection of ports with full digital control and a minimum of external components.
Integrating power, analog and state of the art logic, the PD69101 device fits into a single 24-pin, plastic QFN package. A "plug and play" device, the PD69101 executes all real-time functions as specified in the IEEE 802.3af-2003 ("AF") and IEEE 802.3at High Power ("AT") standards, including load detection, "AF" and "AT" classification, and using Multiple Classification Attempts (MCA).
The PD69101 is designed to detect and disable disconnected ports, utilizing DC disconnection methods, as specified in the IEEE 802.3af-2003 and IEEE 802.3at-2009 standards. It can optionally detect legacy/pre-standard PD devices.
The PD69101 also provides PD protection such as over-load, under-load, over-voltage, over-temperature and short-circuiting. It supports supply voltages ranging from 44V to 57 VDC with no need for additional power supply sources.
The PD69101 is a low power device using an internal 0.34Ω MOSFET and an external 0.5Ω sense resistor. The chip includes built-in internal thermal protection. Two LEDs provide port state's indication and port type (AF/AT). |
PD69104B1IEEE 802.3at / UPoE, 4 ports PSE controller + manager | Power Over Ethernet (PoE) Controllers | 4 | Active | A four-port, mixed-signal, high-voltage PoE Manager. It enables network devices to share power and data over a single cable. PD69104B1 PoE-Manager chip is employed by both Ethernet switches and midspans. The device integrates power, analog circuitry, and state-of-the-art control logic into a single 48-pin plastic quad flat no-leads (QFN) package. PD69104B1 supports the following modes of operation: Microchip extended auto mode: A stand-alone mode in which the PD69104B1 detects IEEE 802.3af-2003 compliant powered devices (PDs) and IEEE 802.3at-2009 high-power devices, ensuring safe power feeding and disconnection of ports based on a power management algorithm while employing a minimum of external components. Semi auto mode: Allows the host to control which devices are powered and which are not, as well as communicate with PD69104B1 and configuring it. PD69104B1 executes all real-time functions as specified in IEEE 802.3AF-2003 (AF) and IEEE 802.3AT high power (AT) standards. This includes load detection, AF and AT classifications. In addition, the PD69104B1 device features Multiple Classification Attempts (MCA) port status monitoring. PD69104B1 supports detection of legacy / pre-standard PD devices. It also provides PD real-time protection through the following mechanisms: overload, under-load, over-voltage, over-temperature, and short-circuit. PD69104B1/F supports supply voltages between 44V and 57V, with no need for additional power supply sources, and has built-in thermal protection. PD69104B1 is a low-power device that uses internal MOSFETs and external 0.36Ω sense resistors. PD69104B1 is available in a 48 lead, 8 mm × 8 mm QFN package. |
| Power Over Ethernet (PoE) Controllers | 1 | Active | |
| Power Over Ethernet (PoE) Controllers | 32 | Obsolete | |
