MAX3222E Series

3- to 5.5-V dual channel 500kbps RS-232 line driver/receiver with +/-15-kV IEC-ESD protection

Catalog

3- to 5.5-V dual channel 500kbps RS-232 line driver/receiver with +/-15-kV IEC-ESD protection

Part	Type	Data Rate	Duplex	Voltage - Supply [Max]	Voltage - Supply [Min]	Mounting Type	Protocol	Supplier Device Package	Operating Temperature [Max]	Operating Temperature [Min]	Package / Case	Receiver Hysteresis	Number of Drivers/Receivers [custom]	Number of Drivers/Receivers [custom]	Package / Case [y]	Package / Case [y]	Package / Case [x]
Texas Instruments MAX3222CDBRE4	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-SSOP	70 °C	0 °C	20-SSOP	300 mV	2	2
Texas Instruments MAX3222IDBR	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-SSOP	85 °C	-40 °C	20-SSOP	300 mV	2	2
Texas Instruments MAX3222CDB	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-SSOP	70 °C	0 °C	20-SSOP	300 mV	2	2
Texas Instruments MAX3222EIDWR	Transceiver	500 kbps	Full	5.5 V	3 V	Surface Mount	RS232	20-SOIC	85 °C	-40 °C	20-SOIC	300 mV	2	2	0.295 in	7.5 mm
Texas Instruments MAX3222CDW	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-SOIC	70 °C	0 °C	20-SOIC	300 mV	2	2	0.295 in	7.5 mm
Texas Instruments MAX3222CPWR	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-TSSOP	70 °C	0 °C	20-TSSOP	300 mV	2	2	4.4 mm		0.173 in
Texas Instruments MAX3222EIDB	Transceiver	500 kbps	Full	5.5 V	3 V	Surface Mount	RS232	20-SSOP	85 °C	-40 °C	20-SSOP	300 mV	2	2
Texas Instruments MAX3222ECPWG4	Transceiver	500 kbps	Full	5.5 V	3 V	Surface Mount	RS232	20-TSSOP	70 °C	0 °C	20-TSSOP	300 mV	2	2	4.4 mm		0.173 in
Texas Instruments MAX3222CDWG4	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-SOIC	70 °C	0 °C	20-SOIC	300 mV	2	2	0.295 in	7.5 mm
Texas Instruments MAX3222IPW	Transceiver	250 KBd	Full	5.5 V	3 V	Surface Mount	RS232	20-TSSOP	85 °C	-40 °C	20-TSSOP	300 mV	2	2	4.4 mm		0.173 in

Catalog

3- to 5.5-V dual channel 500kbps RS-232 line driver/receiver with +/-15-kV IEC-ESD protection

Key Features

• ESD Protection for RS-232 bus pins±15kV Human-body model (HBM)±8kV IEC61000-4-2, Contact discharge±15kV IEC61000-4-2, Air-gap dischargeMeets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standardsOperates with 3V to 5.5V VCC supplyOperates up to 500kbit/sTwo drivers and two receiversLow standby current: 1µA typicalExternal capacitors: 4 × 0.1µFAccepts 5V logic input with 3.3V supplyAlternative high-speed pin-compatible device (1Mbit/s) for SNx5C3222EESD Protection for RS-232 bus pins±15kV Human-body model (HBM)±8kV IEC61000-4-2, Contact discharge±15kV IEC61000-4-2, Air-gap dischargeMeets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standardsOperates with 3V to 5.5V VCC supplyOperates up to 500kbit/sTwo drivers and two receiversLow standby current: 1µA typicalExternal capacitors: 4 × 0.1µFAccepts 5V logic input with 3.3V supplyAlternative high-speed pin-compatible device (1Mbit/s) for SNx5C3222E

Description

The MAX3222E consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3V to 5.5V supply. The device operates at typical data signaling rates up to 500kbit/s and a maximum of 30V/µs driver output slew rate. The MAX3222E can be placed in the power-down mode by setting the power-down ( PWRDOWN) input low, which draws only 1µA from the power supply. When the device is powered down, the receivers remain active while the drivers are placed in the high-impedance state. Also, during power down, the onboard charge pump is disabled; V+ is lowered to VCC, and V– is raised toward GND. Receiver outputs also can be placed in the high-impedance state by setting enable ( EN) high. The MAX3222E consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3V to 5.5V supply. The device operates at typical data signaling rates up to 500kbit/s and a maximum of 30V/µs driver output slew rate. The MAX3222E can be placed in the power-down mode by setting the power-down ( PWRDOWN) input low, which draws only 1µA from the power supply. When the device is powered down, the receivers remain active while the drivers are placed in the high-impedance state. Also, during power down, the onboard charge pump is disabled; V+ is lowered to VCC, and V– is raised toward GND. Receiver outputs also can be placed in the high-impedance state by setting enable ( EN) high.