Catalog
Stellaris LM3S Microcontroller
Key Features
• 32-bit ARM® Cortex™-M325-MHz processor core with System Timer (SysTick), integrated Nested Vectored Interrupt Controller (NVIC),Memory Protection Unit (MPU),and Thumb-2 instruction setFull-featured debug solution with debug access via JTAG and Serial Wire interfaces, and IEEE 1149.1-1990 compliant Test Access Port (TAP) controller64KB single-cycle flash and16KB single-cycle SRAM10-30GPIOs (depending on configuration) with programmable control for GPIO interrupts and pad configurationARM FiRM-compliant Watchdog Timer ; plusthreeGeneral-Purpose Timer Modules (GPTM), each of which provides two 16-bit timers/countersand can be configured to operate independently10-bit Analog-to-Digital Converter (ADC) with analog input channels and a sample rate of samples/secondFullyprogrammable 16C550-type UARTwith IrDA supportSynchronous Serial Interface (SSI), supporting operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfacesHighly configurable 10/100 Ethernet Controller that conforms to the IEEE 802.3-2002 specification with full- and half-duplex modes for both 100 Mbps and 10 Mbps operation, and automatic MDI/MDI-X cross-over correctionOneintegrated analog comparator configurable for output to drive an output pin or generate an interruptIndustrial and extended temperature RoHS-compliant 100-pin LQFP package and industrial-range RoHS-compliant 108-ball BGA package32-bit ARM® Cortex™-M325-MHz processor core with System Timer (SysTick), integrated Nested Vectored Interrupt Controller (NVIC),Memory Protection Unit (MPU),and Thumb-2 instruction setFull-featured debug solution with debug access via JTAG and Serial Wire interfaces, and IEEE 1149.1-1990 compliant Test Access Port (TAP) controller64KB single-cycle flash and16KB single-cycle SRAM10-30GPIOs (depending on configuration) with programmable control for GPIO interrupts and pad configurationARM FiRM-compliant Watchdog Timer ; plusthreeGeneral-Purpose Timer Modules (GPTM), each of which provides two 16-bit timers/countersand can be configured to operate independently10-bit Analog-to-Digital Converter (ADC) with analog input channels and a sample rate of samples/secondFullyprogrammable 16C550-type UARTwith IrDA supportSynchronous Serial Interface (SSI), supporting operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfacesHighly configurable 10/100 Ethernet Controller that conforms to the IEEE 802.3-2002 specification with full- and half-duplex modes for both 100 Mbps and 10 Mbps operation, and automatic MDI/MDI-X cross-over correctionOneintegrated analog comparator configurable for output to drive an output pin or generate an interruptIndustrial and extended temperature RoHS-compliant 100-pin LQFP package and industrial-range RoHS-compliant 108-ball BGA package
Description
AI
The Stellaris® LM3S6100 microcontroller is based on the ARM® Cortex™-M3 controller core operating at up to 25 MHz, with 64 kB flash and 16 kB SRAM. The LM3S6100 also features real-time industrial connectivity, with a 10/100 Ethernet MAC/PHY, an SSI / SPI controller, and a UART. Finally, the LM3S6100 microcontroller provides a 24-bit systick timer, 3 32-bit or 6 16-bit general-purpose timers, a watchdog timer, a low drop-out voltage regulator so that only one supply voltage is required, brown-out reset, power-on reset controller, and up to 30 GPIOs.
The Stellaris® LM3S6100 microcontroller is based on the ARM® Cortex™-M3 controller core operating at up to 25 MHz, with 64 kB flash and 16 kB SRAM. The LM3S6100 also features real-time industrial connectivity, with a 10/100 Ethernet MAC/PHY, an SSI / SPI controller, and a UART. Finally, the LM3S6100 microcontroller provides a 24-bit systick timer, 3 32-bit or 6 16-bit general-purpose timers, a watchdog timer, a low drop-out voltage regulator so that only one supply voltage is required, brown-out reset, power-on reset controller, and up to 30 GPIOs.
