SN65HVD230M-EP Series

Enhanced Product 3.3-V Can Transceivers With Standby Mode

Catalog

Enhanced Product 3.3-V Can Transceivers With Standby Mode

Part	Supplier Device Package	Operating Temperature [Max]	Operating Temperature [Min]	Type	Package / Case	Package / Case [y]	Package / Case [x]	Receiver Hysteresis	Duplex	Protocol	Data Rate	Mounting Type	Voltage - Supply [Max]	Voltage - Supply [Min]	Qualification	Grade	Operating Temperature [Max]	Operating Temperature [Min]
Texas Instruments SN65HVD230QDR	8-SOIC	85 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V
Texas Instruments SN65HVD230DG4	8-SOIC	85 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V
Texas Instruments SN65HVD230QDRG4Q1	8-SOIC	125 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V	AEC-Q100	Automotive
Texas Instruments SN65HVD230QDG4Q1	8-SOIC	125 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V	AEC-Q100	Automotive
Texas Instruments SN65HVD230DRG4	8-SOIC	85 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V
Texas Instruments V62/06629-01XE	8-SOIC			Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V			125 °C	-55 °C
Texas Instruments SN65HVD230MDREP	8-SOIC	125 °C	-55 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V
Texas Instruments SN65HVD230QDRG4	8-SOIC	85 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V
Texas Instruments SN65HVD230QDG4	8-SOIC	125 °C	-40 °C	Transceiver	8-SOIC	3.9 mm	0.154 in	100 mV	Half	CANbus	1 Mbps	Surface Mount	3.6 V	3 V

Catalog

Enhanced Product 3.3-V Can Transceivers With Standby Mode

Key Features

• Controlled BaselineOne Assembly/Test Site, One Fabrication SiteExtended Temperature Performance of -55°C to 125°CEnhanced Diminishing Manufacturing Sources (DMS) SupportEnhanced Product-Change NotificationQualification PedigreeOperates With a 3.3-V SupplyLow Power Replacement for the PCA82C250 FootprintBus/Pin ESD Protection Exceeds 15-kV HBMControlled Driver Output Transition Times for Improved Signal Quality on the SN65HVD230MUnpowered Node Does Not Disturb the BusCompatible With the Requirements of the ISO 11898 StandardLow-Current SN65HVD230M Standby Mode 370 µA TypicalDesigned for Signaling RatesUp To 1 Megabit/Second (Mbps)Thermal Shutdown ProtectionOpen-Circuit Fail-Safe DesignComponent qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits.The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).Controlled BaselineOne Assembly/Test Site, One Fabrication SiteExtended Temperature Performance of -55°C to 125°CEnhanced Diminishing Manufacturing Sources (DMS) SupportEnhanced Product-Change NotificationQualification PedigreeOperates With a 3.3-V SupplyLow Power Replacement for the PCA82C250 FootprintBus/Pin ESD Protection Exceeds 15-kV HBMControlled Driver Output Transition Times for Improved Signal Quality on the SN65HVD230MUnpowered Node Does Not Disturb the BusCompatible With the Requirements of the ISO 11898 StandardLow-Current SN65HVD230M Standby Mode 370 µA TypicalDesigned for Signaling RatesUp To 1 Megabit/Second (Mbps)Thermal Shutdown ProtectionOpen-Circuit Fail-Safe DesignComponent qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits.The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).

Description

The SN65HVD230Q, SN65HVD231Q, and SN65HVD232Q controller area network (CAN) transceivers are designed for use with the Texas Instruments TMS320Lx240x 3.3-V DSPs with CAN controllers, or with equivalent devices. They are intended for use in applications employing the CAN serial communication physical layer in accordance with the ISO 11898 standard. Each CAN transceiver is designed to provide differential transmit capability to the bus and differential receive capability to a CAN controller at speeds up to 1 Mbps. Designed for operation in especially-harsh environments, these devices feature cross-wire protection, loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range. The transceiver interfaces the single-ended CAN controller with the differential CAN bus found in industrial, building automation, and automotive applications. It operates over a –2-V to 7-V common-mode range on the bus, and it can withstand common-mode transients of ±25 V. On the SN65HVD230Q and SN65HVD231Q, RS(pin 8) provides three different modes of operation: high-speed, slope control, and low-power modes. The high-speed mode of operation is selected by connecting pin 8 to ground, allowing the transmitter output transistors to switch on and off as fast as possible with no limitation on the rise and fall slopes. The rise and fall slopes can be adjusted by connecting a resistor to ground at pin 8, since the slope is proportional to the pin’s output current. This slope control is implemented with external resistor values of 10 k, to achieve a 15-V/µs slew rate, to 100 k, to achieve a 2-V/µs slew rate. The circuit of the SN65HVD230Q enters a low-current standby mode during which the driver is switched off and the receiver remains active if a high logic level is applied to RS (pin 8). The DSP controller reverses this low-current standby mode when a dominant state (bus differential voltage > 900 mV typical) occurs on the bus. The unique difference between the SN65HVD230Q and the SN65HVD231Q is that both the driver and the receiver are switched off in the SN65HVD231Q when a high logic level is applied to RS(pin 8) and remain in this sleep mode until the circuit is reactivated by a low logic level on RS. The Vref(pin 5 on the SN65HVD230Q and SN65HVD231Q) is available as a VCC/2 voltage reference. The SN65HVD232Q is a basic CAN transceiver with no added options; pins 5 and 8 are NC, no connection. The SN65HVD230Q, SN65HVD231Q, and SN65HVD232Q controller area network (CAN) transceivers are designed for use with the Texas Instruments TMS320Lx240x 3.3-V DSPs with CAN controllers, or with equivalent devices. They are intended for use in applications employing the CAN serial communication physical layer in accordance with the ISO 11898 standard. Each CAN transceiver is designed to provide differential transmit capability to the bus and differential receive capability to a CAN controller at speeds up to 1 Mbps. Designed for operation in especially-harsh environments, these devices feature cross-wire protection, loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range. The transceiver interfaces the single-ended CAN controller with the differential CAN bus found in industrial, building automation, and automotive applications. It operates over a –2-V to 7-V common-mode range on the bus, and it can withstand common-mode transients of ±25 V. On the SN65HVD230Q and SN65HVD231Q, RS(pin 8) provides three different modes of operation: high-speed, slope control, and low-power modes. The high-speed mode of operation is selected by connecting pin 8 to ground, allowing the transmitter output transistors to switch on and off as fast as possible with no limitation on the rise and fall slopes. The rise and fall slopes can be adjusted by connecting a resistor to ground at pin 8, since the slope is proportional to the pin’s output current. This slope control is implemented with external resistor values of 10 k, to achieve a 15-V/µs slew rate, to 100 k, to achieve a 2-V/µs slew rate. The circuit of the SN65HVD230Q enters a low-current standby mode during which the driver is switched off and the receiver remains active if a high logic level is applied to RS (pin 8). The DSP controller reverses this low-current standby mode when a dominant state (bus differential voltage > 900 mV typical) occurs on the bus. The unique difference between the SN65HVD230Q and the SN65HVD231Q is that both the driver and the receiver are switched off in the SN65HVD231Q when a high logic level is applied to RS(pin 8) and remain in this sleep mode until the circuit is reactivated by a low logic level on RS. The Vref(pin 5 on the SN65HVD230Q and SN65HVD231Q) is available as a VCC/2 voltage reference. The SN65HVD232Q is a basic CAN transceiver with no added options; pins 5 and 8 are NC, no connection.